What thicknesses and sizes are available for solid aluminum panels?

Solid aluminum panels for architectural cladding are typically supplied in thicknesses from 1.5 mm to 4.0 mm, with 2.0 mm, 2.5 mm, and 3.0 mm being the most common for exterior facades. Standard sheet sizes are 1220 mm × 2440 mm and 1500 mm × 3000 mm, but custom widths up to 2000 mm and lengths up to 6000 mm can be produced depending on the supplier’s equipment. The final thickness and size must be confirmed against your project’s structural requirements, wind load, flatness tolerance, and design intent. Always request a shop drawing review and a sample before ordering.
1. Thickness: what the numbers mean and how to choose
When buyers ask about “thickness,” they usually mean the base metal thickness (the aluminum sheet before coating). This is different from the overall thickness after painting, which adds typically 25–60 microns depending on the coating system. Always specify base metal thickness in your purchase order to avoid confusion.
Common thickness ranges and typical applications
- 1.5 mm – 2.0 mm: Interior wall cladding, signage, ceilings, and low-rise exterior features where wind load is moderate. Often used for decorative panels.
- 2.5 mm – 3.0 mm: Standard exterior facade panels for low- to mid-rise buildings. Provides good rigidity and flatness for large panel sizes.
- 3.5 mm – 4.0 mm: High-rise facades, areas with high wind pressure, or panels with large spans. Also used where extra impact resistance is needed.
These are general industry ranges. The correct thickness for your project depends on:
- Wind load calculations (especially for tall buildings or coastal areas).
- Panel size and support spacing (larger panels need greater stiffness).
- Flatness requirements (thinner panels may show oil-canning).
- Local building codes and fire performance requirements.
Your structural engineer or facade consultant should specify the minimum thickness. Do not rely on a supplier’s stock thickness alone.
Thickness tolerances
Aluminum sheet thickness is subject to manufacturing tolerances. For example, a 3.0 mm nominal sheet may have a tolerance of ±0.1 mm or ±0.15 mm depending on the standard applied. Ask your supplier what tolerance they work to and whether they can provide mill certificates. For critical projects, specify the tolerance in the purchase order and request inspection reports.
2. Panel sizes: standard and custom
Solid aluminum panels are fabricated from flat sheets that are cut, folded, and welded to form a tray shape. The finished panel size is usually smaller than the raw sheet size because of the folded edges (typically 20–30 mm returns). When discussing sizes, clarify whether you are referring to the flat sheet size or the finished panel face size.
Standard sheet sizes
- 1220 mm × 2440 mm (4 ft × 8 ft) – the most common size, widely available and cost-effective.
- 1500 mm × 3000 mm – used for larger panels, reducing the number of joints.
- 1000 mm × 2000 mm – sometimes used for smaller projects or where handling is restricted.
These are typical stock sizes; availability varies by supplier and region. Custom sizes can be cut from larger coils or sheets.
Maximum and custom sizes
Many manufacturers can produce panels up to 2000 mm wide and 6000 mm long, but these limits depend on the supplier’s press brake, welding, and coating line capabilities. For very large panels, consider:
- Transport restrictions (truck or container dimensions).
- Handling and installation equipment on site.
- Potential for deformation during baking or coating.
Always confirm the maximum panel size with your supplier before finalizing the design. If your design requires panels beyond the supplier’s capacity, you may need to split them or choose a different material.
3. How thickness and size affect performance and cost
Thickness and size are directly linked to cost and performance:
- Thicker panels increase material cost and weight, but improve rigidity and flatness. They may also require stronger supporting frames.
- Larger panels reduce installation labor and joints, but increase handling and transport costs, and may require thicker material to maintain flatness.
- Coating thickness adds to the overall thickness but has a minor effect on structural performance. However, coating type and thickness are critical for weather resistance and color retention.
When comparing quotes, ensure that the thickness and size are specified in the same way. A quote for “3 mm panel” may refer to base metal or overall thickness; clarify this upfront.
4. What to confirm with your supplier
Because every project is different, the following items must be confirmed with your supplier before ordering:
- Base metal thickness and tolerance – ask for the mill certificate or test report.
- Alloy and temper – common alloys are 1100, 3003, and 5005; the choice affects strength and formability.
- Maximum panel size – confirm the supplier’s equipment limits and whether they can produce your required dimensions.
- Flatness tolerance – especially for large panels; ask for the standard they follow.
- Coating system – PVDF, polyester, or powder coating; each has different thickness and performance characteristics.
- Packing and transport – large panels require special crating to prevent damage; confirm packing details and loading quantities.
- Samples – request a sample of the proposed thickness and finish to verify appearance and quality.
- MOQ – minimum order quantity varies by supplier and is often based on total square meters or number of panels; confirm this before quoting.
- Lead time – depends on current production schedule, coating line availability, and order size; ask for a confirmed schedule after drawing approval.
Note: Our company does not publish fixed MOQ, prices, or lead times because these depend on the specific project requirements, quantity, finish, and destination. Please contact us with your drawings and specifications for a tailored quotation.
5. Information needed for an accurate inquiry
To receive a precise and comparable quotation, please provide:
- Project location and building height (for wind load considerations).
- Architectural drawings or sketches showing panel sizes, shapes, and quantities.
- Required base metal thickness and alloy (if specified).
- Surface finish (PVDF color, polyester, powder coating, anodized, etc.) with color reference.
- Any special requirements: perforations, louvers, curved panels, fire rating, etc.
- Delivery destination and preferred trade terms (e.g., FOB, CIF) – we will clarify responsibilities and costs.
- Required certification or test reports (e.g., mill certificate, coating performance).
With these details, we can confirm technical feasibility, provide a sample, and quote accurately.
Contact us
For further assistance with your solid aluminum panel specification, please reach out to our team:
- Company: 金霸建材(广东)有限公司
- Contact person: 张经理
- Email: [email protected]
- WeChat: 13823463551
- Website: https://aocao.cn
- Address: 广东省佛山市南海区
We are happy to review your drawings and discuss your project requirements.