What thicknesses and sizes are available for solid aluminum panels?

What thicknesses and sizes are available for solid aluminum panels?

Solid aluminum panels are usually specified by three separate dimensions: base metal thickness, coating thickness, and finished panel size. In common architectural practice, single-skin solid aluminum panels are produced in base thicknesses from about 1.5 mm to 4.0 mm, with 2.0 mm, 2.5 mm, and 3.0 mm being the most frequently requested for exterior facades. Finished panel widths are often limited by coil width and forming equipment, while panel lengths depend on handling, transport, and the structural span between supports. The exact thickness and size for your project must be confirmed against the architectural drawings, wind-load calculation, finish, quantity, packing method, and destination. No universal stock list applies to every supplier or every project.

Base metal thickness: what the numbers mean

Base metal thickness is the thickness of the aluminum sheet before any coating is applied. It is the value that governs stiffness, flatness, and the panel's ability to span between sub-frame supports. Buyers should not confuse base metal thickness with total coated thickness. A 2.5 mm panel with a 25-micron coating is still a 2.5 mm base panel.

Typical architectural ranges include:

These ranges are general industry practice, not a guarantee of what any particular supplier stocks. Thickness selection is a design decision that should be verified by a structural engineer or facade consultant, especially for Canada projects where snow, wind, and thermal cycling vary by province and elevation.

Coating thickness and finish: a separate specification

Coating thickness is specified separately from base metal thickness. For liquid fluorocarbon coatings, common dry-film thicknesses are around 25 to 35 microns for a two-coat system and 35 to 45 microns for a three-coat system. Powder coatings are often specified at 60 to 80 microns. These figures are typical reference values, not a compliance claim. The buyer should confirm the coating system, dry-film thickness, color tolerance, gloss level, and test standard with the supplier and, where required, with an independent testing laboratory.

Coating choice affects price, lead time, and durability. It does not change the base metal thickness. When comparing quotations, ask each supplier to state base thickness and coating thickness separately so that offers are comparable.

Panel width and length: what limits the finished size

Finished panel size is constrained by several practical factors:

Because these limits vary by supplier and by project, buyers should provide a panel schedule with maximum and minimum dimensions rather than asking for a single generic size. The supplier can then confirm which sizes are feasible with the available coil, equipment, and packing method.

How thickness and size interact with price and delivery

Thickness and size are two of the largest cost drivers for solid aluminum panels. A thicker base metal uses more aluminum, which is the dominant material cost. A larger panel size increases waste, handling, packing, and transport cost. Coating type, color, and surface treatment add further cost. Quantity affects setup and unit pricing. Packing method and destination affect freight and insurance.

For these reasons, a responsible supplier cannot quote a firm unit price from a thickness and size alone. The buyer should expect to provide drawings, a panel schedule, finish requirements, quantity, packing preference, and delivery destination before receiving a meaningful quotation. Any price or lead time given without these inputs is an estimate, not a commitment.

What to confirm before ordering

Use the following checklist to avoid specification gaps:

  1. Base metal thickness for each panel type, stated in millimeters and referenced to the drawing.
  2. Alloy and temper if the project requires a specific grade; this must be confirmed with the supplier and, where applicable, supported by mill certificates.
  3. Coating system and dry-film thickness, including color, gloss, and any required test standard.
  4. Finished panel dimensions, including width, length, return flanges, stiffeners, and cutouts.
  5. Structural verification that the selected thickness and support spacing meet the project's wind-load and deflection criteria.
  6. Sample approval before mass production, so that color, gloss, and flatness are agreed in writing.
  7. Packing method and any destination-specific handling requirements.
  8. Quantity and delivery schedule, recognizing that final lead time depends on drawing approval, sample approval, material availability, production queue, coating, quality inspection, and packing.

Do not assume that a supplier holds a particular thickness or size in stock. Stock availability changes with market conditions and project demand. Confirm current availability at the time of inquiry.

How to request a quotation

To receive a comparable quotation for solid aluminum panels, send the following information:

With these details, a supplier can confirm feasible thicknesses and sizes, propose a coating system, and provide a quotation that reflects the actual scope. Final values for thickness, size, price, lead time, and packing depend on drawings, finish, quantity, testing standard, packing, and destination.

For project-specific questions about solid aluminum panels, you can contact 金霸建材(广东)有限公司. Email: [email protected]. WeChat: 13823463551. Website: https://aocao.cn. Contact person: 张经理. Address: 广东省佛山市南海区.

Back to news