What thicknesses and sizes are available for solid aluminum panels?

What thicknesses and sizes are available for solid aluminum panels?

Solid aluminum panels are most commonly specified in base metal thicknesses of 1.5 mm, 2.0 mm, 2.5 mm, 3.0 mm, 4.0 mm, 5.0 mm and 6.0 mm. For exterior building facades, 2.0 mm to 4.0 mm is the usual working range, while 1.5 mm is often used for interior linings, signage and low-rise decorative work. Panel width and length are not fixed by a single global standard: they depend on the alloy and temper, the coil width available, the coating line, the fabrication equipment and the transport limits for the finished crate. A buyer should therefore treat thickness and size as two separate confirmation items, not as a single catalogue number.

Base metal thickness versus total panel thickness

In solid aluminum panel procurement, the thickness that matters for structural calculation is the base metal thickness, sometimes called the core or sheet thickness. The total panel thickness after coating is slightly greater because the paint film adds a thin layer on the surface. If a drawing calls for 3.0 mm aluminum panel, the supplier should confirm whether this means 3.0 mm base metal or 3.0 mm overall. This distinction affects weight, stiffness, wind-load performance and cost. A buyer should ask for the thickness definition in writing before comparing quotations.

Thickness tolerance is also a verification item. Different mills and different product standards allow different minus tolerances. The buyer should state the acceptable tolerance range in the purchase order and, where the project requires it, ask for a mill certificate or incoming inspection report. Do not assume that a nominal 3.0 mm sheet measures exactly 3.0 mm at every point.

Common sizes and how they are limited

Solid aluminum panels are usually supplied as flat sheets or as fabricated panels with bent edges, stiffeners and mounting brackets. Standard flat sheet widths often fall between 1000 mm and 1500 mm, and lengths can run to 3000 mm or more depending on the supplier. However, these are general industry ranges, not a guaranteed stock list. The practical maximum size for a finished panel is limited by:

  • Coil and sheet width: the coating line and the shear can only handle certain widths.
  • Alloy and temper: softer tempers may sag or mark during handling; harder tempers may crack at tight bend radii.
  • Flatness and stiffness: larger panels need more stiffeners or a thicker gauge to stay flat.
  • Coating and curing: the oven and conveyor dimensions limit panel length.
  • Packing and transport: very long panels require special crates and may exceed container or truck limits.

Because these limits vary by factory, the buyer should send the actual panel schedule, including width, length, bend details and stiffener layout, and ask the supplier to confirm which sizes can be produced without joints or extra reinforcement.

How thickness is chosen for a project

Thickness selection is a design decision, not a catalogue default. The main factors are:

  1. Wind load and height: higher wind pressure and greater building height usually require thicker metal or closer stiffener spacing.
  2. Panel span: the distance between supports or stiffeners affects deflection.
  3. Flatness requirement: visible facades often need tighter flatness than hidden areas.
  4. Finish and color: some coatings and colors show waviness more easily.
  5. Fabrication: edge bends, returns and corner details need enough metal thickness to form cleanly.
  6. Weight limits: the supporting structure and the lifting equipment may set a maximum panel weight.

The buyer should provide the structural engineer's required thickness or the design load, and ask the panel supplier to confirm whether the proposed thickness and stiffener pattern meet it. The final value depends on drawings, finish, quantity, testing standard, packing and destination.

Coating thickness is separate from metal thickness

Coating thickness is often quoted in microns and is not the same as base metal thickness. A liquid fluorocarbon coating, for example, may be specified as a certain dry film thickness, while a powder coating or anodized finish has its own measurement method. Buyers should ask for the coating specification separately: system name, primer, topcoat, dry film thickness, color standard and gloss range. If the project requires a specific performance standard, that standard should be listed as a buyer verification item and confirmed by test report, not assumed from a brochure.

What to confirm before requesting a quotation

To get a comparable quotation, prepare the following information:

  • Base metal thickness and tolerance, or the structural requirement.
  • Alloy and temper, if specified by the designer.
  • Panel width, length, quantity and any cut-outs or perforations.
  • Edge details, stiffeners, brackets and whether fabrication is required.
  • Surface finish system, color reference and gloss.
  • Flatness and visual acceptance criteria.
  • Packing method and delivery destination.
  • Any required test reports or third-party inspection.

Without these details, a supplier can only give an indicative range, and the final price and lead time will change after the drawings are reviewed.

Sample and order confirmation

Samples are useful for checking color, gloss and surface texture, but a small sample may not represent the flatness of a full-size panel. Buyers should ask whether the sample is made from the same alloy, temper and coating system as the production order. MOQ, sample charges and delivery schedules are commercial terms that depend on the factory's current production plan and the specific panel size; these should be confirmed directly with the supplier rather than assumed from a general article.

Contact for drawing review

If you have a panel schedule or facade drawing, send it for a thickness and size review. The final specification depends on the drawing, finish, quantity, testing standard, packing and destination. You can reach us through the following channels:

  • Company: 金霸建材(广东)有限公司
  • Website: https://aocao.cn
  • Email: [email protected]
  • WeChat: 13823463551
  • Contact person: 张经理
  • Address: 广东省佛山市南海区

When you inquire, please include the base metal thickness, panel sizes, alloy or design requirement, finish system, quantity and delivery location so that the supplier can confirm what is feasible and what needs to be verified.

Back to news